Serving the Jackson area  ·  (601) 213-0169  ·  Open Mon-Sun 7am-7pm
📞 (601) 213-0169 Free Quote

Metal Roofing in Pearl, MS (39208) · Local Professionals

Jackson Metal Roofing · Fast response in Pearl and the Jackson area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+352Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Pearl runs on pine shade and aging shingles. East of the Pearl River, the 1970s to 2000s brick ranches and two-story subdivisions off Highway 80 and Pearson Road are hitting the age where fasteners back out, seams separate, and attic heat turns a small leak into a ceiling stain.

We are Jackson Metal Roofing, and we work Pearl (39208) and the surrounding Jackson area every week. From the older streets near Pearl High School to the newer builds out toward the Ross Barnett Reservoir, we know how these roofs fail and how to fix them without selling you a whole new roof you do not need.

Metal Roofing in Pearl (39208)

Pearl sits in the Pearl River valley on rolling Yazoo clay, and that clay moves. It swells after a week of thunderstorms and shrinks in a dry July, which racks the framing on older homes and opens gaps at flashings and valleys. Add tall loblolly pines dropping needles into every roof valley and water oak limbs over the driveways, and you get the two things we see most in Pearl: moisture trapped in valleys and fasteners that have worked loose after 15 or 20 years of summer heat and straight-line wind. The low-slope roofs on the mid-century ranches near Highway 80 are a different animal, and they need panels and underlayment detailed for slow drainage, not a standard pitch install.

Our team has been on roofs across Rankin and Hinds counties long enough to know which Pearl subdivisions have tight lot access, which streets have HOA design review, and which older homes still carry two layers of shingles under the current roof. We are fully insured with general liability and workers' compensation, and we pull permits through the City of Pearl before a full replacement, so the inspection is on record when you sell.

Our services in Pearl

How a Job Works in Pearl

Step 1: you call (601) 213-0169 or send a message, and we set a free on-site assessment. We walk the roof, check the attic if you have one, look at the valleys and flashings, and tell you plainly whether you are looking at a repair, a re-fastening, or a replacement. You get a written estimate, not a number shouted from the ladder.

Step 2: once you approve, we schedule the work and handle the City of Pearl permit if the job needs one. On the tighter lots east of the river, we stage materials in the driveway and keep the dumpster off the street where we can. If your subdivision has an HOA with design review, we help you get the panel profile and color approved before anything is ordered.

Step 3: we clean up. That means magnet sweeps for screws and nails, a walk of the yard and gutters, and a final walkthrough with you on the roof or at the edge of it. We do not leave until you have seen the finished work and know what to watch for.

Pricing in Pearl is straightforward and depends on the job. Metal roof repair and leak repair start at $450, and screw replacement and re-fastening starts at $750, which is the steady work on these pine-shaded lots. A full metal roof installation starts around $8 per square foot, standing seam around $10, metal roof replacement around $9, and a retrofit over existing shingles around $7. Corrugated and ribbed panel roofing starts at $5.50 per square foot, and coating or painting an existing metal roof starts at $2.50. Size, roof pitch, access, how many layers are already up there, and how urgent the leak is all move the number. Call (601) 213-0169 for a free estimate and a real figure for your address.

My 1980s ranch off Pearson Road has shingles and I keep finding granules in the gutters. Is that a repair or a replacement?
Granules in the gutters on a roof that age usually mean the shingle mat is near the end of its life, especially on the south and west slopes where the Pearl summer sun hits hardest. We will get on the roof and check for curling, exposed fasteners, and soft spots before we recommend anything. Sometimes a repair buys you a few more years. Sometimes it is time to plan the replacement, and we will tell you which one it is.
A storm just peeled back panels on my barn off Old Brandon Road. How fast can you get out?
Storm and wind damage calls get priority. We offer a free inspection, and we can usually get eyes on a Pearl property within a day or two of your call. Call (601) 213-0169, and if there is an active leak, we will talk you through temporary protection until we are on site.
What does a metal roof actually cost for a typical Pearl subdivision house?
For a standard 1,800 to 2,200 square foot ranch or two-story in Pearl, most full metal roof installations land somewhere in the range you would expect from the per-square-foot prices above, with standing seam at the higher end and corrugated panel at the lower end. The variables are roof complexity, how many layers need to come off, and whether you are retrofitting over shingles. A free estimate at (601) 213-0169 gets you a firm number.
Do I need a permit from the City of Pearl to replace my roof?
A full replacement or re-roof commonly requires a permit through the City of Pearl, and the threshold, fee, and inspection requirements can vary, so we confirm the current rules with the building department before we start. We pull the permit and schedule the inspection as part of the job. If you are in an HOA or a historic review area, that approval is separate and we help you work through it.
My neighbor's pine drops needles all over my roof and my HOA wants a specific color. What do I do?
Property line rules in Mississippi let you trim limbs that cross onto your side, but anything on the neighbor's side is a conversation, not a right. On the HOA side, we can give you the panel profile and color samples to submit for design review before you commit. Pine needle buildup in valleys is worth clearing twice a year, because that is where moisture sits and seams start to fail.
Are you covered if someone gets hurt on my Pearl property during the job?
Yes. That protects you as the homeowner if anything happens on the roof or in the yard during the project.
What maintenance should I do between now and storm season in Pearl?
Clear pine needles and oak leaves out of the valleys and off the low-slope sections, especially on the north side where they stay wet longest. Check the gutters after the spring pollen drop, and look for lifted or backed-out screws after any wind event. A free inspection in late winter, before the March to May squalls, catches most of the small stuff before it becomes a ceiling repair.
Why choose us?

Trusted professionals in Jackson

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Jackson

All your work handled by qualified professionals in Jackson

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

352+ Verified Client Reviews in Jackson

⭐⭐⭐⭐⭐ 4.9/5 · 352 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Jackson · Response within 24h · No commitment · ☎ (601) 213-0169

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Jackson ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm